obvioubsly being overly pendament in nature, I 'd have to state WAY Much!;)
got to take the cat by surprise at less than 4min, 54 sesk in a high statement of surprise! Either I am too bored or I have too much time or bestly a mix both!!!
Take care my fellow Forumimtes
Just got an email saying, "your order has shipped".. FINALLY!
Looking forward to see how they look, especially in 1080i Upconversion mode... may have to get High Definition copies (Blu-ray or HD-DVD, as applicable) if they warrant the look...
8^)
You got that right... go to the following message to read about P30 and it's problems...
http://evga.com/forums/tm.asp?m=77862
I rolled back to P29 and have NO more problems.. couldn't O/C a bit (well, 5 whole MHz, whoo hoo.. 8^/ ) Now running an E6850 at 4005 MHz, 1.53 vcc, TR 120...
Installed the new beta bios, no problems yet. As a side bonus, it seems to have upped my Sandra Memory Bandwidth benchmark by almost 400 MB/s, to ~7600 MB/s... I have not had the SATA errors problem widely reported, but I did have an intemittent "drive busy light" that would occasionally pop up...
I too, had to initiate a charge-back to get a refund for a cancelled order I placed in early October with Monarch. They showed in stock for a HSF I ordered, but after two weeks and no shipment, I called and cancelled the order. They said it would take two weeks to process the refund.
It never...
I've got a new EVGA 680i motherboard with an E6600 processor running at 3.6 GHz and it seems to be quite stable (orthos for 24 hours ran fine) and I'm missing the convenience of Motherboard monitor I used to have on my desktop.
Is there any comparable program available that is compatible with...
Got mine today, too. Retail boxed 6300, cheap Intel motherboard, and the same RC1 copy of Vista Ultimate 32bit and 64bit.
I'll be selling both the processor and motherboard on Ebay for some low price and upgrading to an Asus P5N32-E SLI motherboard and a 6600 cpu. Still have to get the ram and...
Yes, the shroud is rather deep, but my case is quite large (full tower) and the power supply is at the middle of the case, rather than the top, so I was able to cut the full 6" hole for the fan and mount the heatercore above the power supply. And with the shroud, the heatercore stands about 1...
I used aluminum flashing to construct a shroud that is about 2 inches deep, from my 172mm fan to the heater core radiator and run the fan at 7 volts, which gives me about 115 cfm (down from 240 cfm at 12V!) and great temps. Yes, my case is rather large, so I am able to put that big contraption...
Does the Dangerden TDX block include the #2, 3, 4 and 5 nozzles? and the blank? And of course, does it include the mounting hardware?
If so, I may be interested... my maze4 is doing well, but the TDX is known to be a better block because of the nozzle acceleration...
Let me know!
Uh, NO. The rebate form says it is valid with ALL RETAILERS, **EXCEPT** for a list including: BJ's, Circuit City, CompuUSA, Costco, Fry's, J&R, Micro Center, Nationwide Marketing Group, Navy Exchange, Nebraska Furniture Mart, Office Depot, OfficeMax, Outpost.com, Staples, Ultimate Electronics...
No, they are not in a RAID 0 configuration. They are just added as additional storage (preferrably to replace the old PATA drives).
I'd rather not do a clean install, just because I have so much other programs to reinstall if I do...
But keep the suggestions coming!
I've got two existing PATA drives with my windows XP installation and files on them. I want to add two SATA 300 GB drives, to my SATA Master 1 and SATA Master 2 (Nvidia) plugs and transfer the existing installation and files to them.
What' s the best way to do this? All drives are Maxtor, and...
Mine is working very well. At 2655 MHz, the CPU temps stay at 31 C, motherboard at 25C. Can't hear the fan much at all, certainly not over the rather loud fan on the 7800 GT I'm running with... Just be sure to line the exhaust direction up with the exhaust fan on the rear of the case.
Well, I'm using this same OCZ memory on an A8N-SLI-Premium, running currently at 265 MHz, at 2.5-3-3-7 timings. It is supremely stable and even cool to the touch (2.8V VDimm).
It was not cheap, but it is very good memory!
It was for $9.99, at Amazon: http://www.amazon.com/exec/obidos/tg/detail/-/B0000CFY7I/qid=1105211427/sr=8-1/ref=pd_csp_1/102-8935060-4129719?v=glance&s=electronics&n=507846
Got three packs of these, handed them out to the grandkids for use in their game machines - the ones that have five...
...Gave up on this motherboard... sold it for $20 the same day I got an Epox 8RDA3i motherboard, which installed perfectly and works perfectly. Not to mention it has a much faster IDE chip on board; testing out at ~50MB/sec on the harddrive, whereas it used to bench about ~37MB/sec on the 8KHA+...
Folks, hope you can help me...
My son's box, which I built several years ago, has a strange problem... Windows Media Player locks up whenever it plays either an .avi or .wmp file. Just as it gets to "opening media", it locks the computer up tight... every time.
Systems specs are: Epox 8KHA+...
Um, the correct stock number is 504516...
Your number gets a Pacific Digital DVR+/- R/RW drive...
But the price is right! $99.94 for an 8 MB buffer, 160 GB drive!
Thanks for a heads-up on a great deal.:cool:
Thanks for the reply. Yeah, I'm about to go ahead and purchase the NF7-S, it's only $50. That's with all the cables, backplate, manual, SATA adaptor, CD-ROM, Floppy, etc.
I'm mainly interested in the higher voltages the NF7-S provides compared to the 8RDA+ I'm currently using. Hopefully, I...
As the title says, what are the differences between the two revisions?
Any capability changes??
Just wondering, have a chance to buy a v1.2 for a real steal...
Should I wait for a v2.0?
Thanks in advance!;)