Kingston 1GB DDR2-5300, have 5 sticks total, 5GB
Samsung DDR2-6400 2x1GB
and the other i think is hynix, 2x512mb PC2-6400
take the entire lot for $45 shipped
I have 12gb (6x2gb) of xms3 corsair 1600MHz ram. when they are all connected to the board the computer will attempt to post once, MemOK LED stays lit and then hangs there and restarts. same thing happens again, Hangs at MemOK LED, and restarts, no display either.
third time around the computer...
I have a black Xbox 360 Elite flashed with the newest LT 3.0 firmware, loads backups fine, no RROD or anything. has a BenQ drive which is really quiet. no issues with the console at all.
it is BANNED from XBOX LIVE however. I purchased it like this some time ago and just used it to play...
Just recently we experienced a bad thunderstorm (NYC) and a very lound thunder strike caused my computer to just shut off along with the tv, connected to a power surge ofc. my machine now refuses to turn on, the green light on the motherboard stays solid but nothing powers up. no signs of any...
Had a wierd issue earlier while i was browsing, the screen went black out of nowhere but the monitor wasn't on standby. i reset the computer numerous times and it shows the SABERTOOTH X58 Logo for about 1 second and goes black, as before the monitor doesn't go to standby either. tried pulling...
I have a 6x2gb kit of standard corsair xms3 1600MHz ram rated at 1.60v, picture below. it's a
CM3X2G1600C9B6, cpu z below. i currently have an overclock on my i930 @ 4GHZ 20x200, what do you guys think i should run my ram at and what timings?
http://i49.tinypic.com/20u2u85.jpg
might be a longshot but i'm looking to put my setup into a lanbox case that i have and keep it as a backup as i plan to upgrade soon. The board comes with all acessories and box with manuals and is in flawless condition.
Bare drive, can include a SATA cable and SATA to Molex if needed. works great, no clicking, absolutely silent, runs cool. asking 42 shipped paypal. heat under "euge". offer!
Picked up this mouse recently from a member here and can't get used to it, it has red LEDs and is in pristine condition. mouse skates have about 90% of life left on them. looking to trade it for a deathadder or something similar, and if needed I can throw in a few bucks also
Just looking for something small like a 60GB to bring back some life to a old Thinkpad R61 i have laying around.. also some ram wound be nice, preferably 2 x 2gb. i have a 1GB DDR3 1333 and a 2GB DDR3 1066 SODIMMs up for grabs..
was thinkin of ebaying my current setup, what do you guys think I could get for it on ebay if i list it as a buy it now?
i7 930 @ 4GHz
ASUS Sabertooth x58
BFG EX-1000 Power Supply
Crucial M4 128GB SSD SATA 3
Western Digital Caviar Blue 640GB
EVGA GTX 460 768MB
12gb Corsair XMS3 1600...
Just looking for something cheap to test alot of old 775 hardware i have lying around. a P4 Prescott will do fine just so i can get it to boot up. not looking to spend a whole lot on one, hopefully someone will let one go for the price of shipping... anything will do
looking for around 2-3 of these fans, some good YATE LOONS or NOCTUAS preferred.. 120mm or 140mm.. if you have any with LED's that would be nice... also have a Sparkle 9500GT 1GB GPU for trade
looking for any of these cards in the 50 dollar range, any brand any core doesnt matter. looking to help a friend out with a cheap upgrade to his computer.
OC'd my 930 to 4GHz stable @ 20x200 with my ram @ 1600 in bios. however in CPU-Z my BCLK Frequency is 190.5 and multi @ 21.0 with my ram @ 761MHz.. CPU-Z Below
http://i49.tinypic.com/qxjxbb.jpg
is it a bug within CPU-Z?
Lol
http://i48.tinypic.com/sfjiut.jpg
http://i48.tinypic.com/14914ea.jpg
currently using zip ties to hold the heatsink down since the bracket got stripped. also my temps are worse, i changed the fluid to distilled water and bled it thoroughly. my pump reads 1680ish rpm and drops down for...
Corsair H50 with all screws and mounting brackets (775,1366,1155/56, AM2/3) and the stock 120mm Fan. also lapped for better heat transfer, lowered my temps by about 4c.
40 shipped to your door. heatware under euGe
I have the following for sale,
Western Digital Caviar Green 500GB 3.5" hard drive - 40 obo
uneec 400w atx power supply - 25
evga gtx 460 768mb - bare card... 85
sparkle 9500GT 1GB - glued a 60mm fan to the heatsink, runs at about 32c idle. 20 shipped
Heatware under "euGe"
recently picked up a corsair h50 off a member here. was coming from a gemini ii s heatsink.
i'm using intel burn test on my q6600 g0 with a vid of 1.325 (terrible) while running stock @ 2.4ghz and the highest temp reading was 60c. the cpu and cooler are also lapped perfectly flat.. could this...
got a 2400xt that i found lying around and like to use in my htpc for it's audio capabilities, it has this weird adapter port...
http://i1221.photobucket.com/albums/dd468/dnbduo/IMG_20110822_225609.jpg
can anyone tell me what it's called? and if possible a link on where i can buy an plug...
got a older rig here with a p5kpl-am epu board with very limited oc options, trying to get 2.8ghz out of it but it wont post over 348fsb.. the overclock setting for the ram only has 3 options, 667 800 and 1066, when i enter 333fsb and set the ram to 667 i get a frequency of 416mhz for the ram in...
i have a 700w ocz power supply and the problem is in the 24 pin atx connector. if i plug it in any board i get no display just fans spinning, but it works fine with matx boards. i tested the voltage out on every pin and its putting out fine voltages. im using another power supply's 24 pin...
I've got a 700W ModXStream Pro that has a defective 4/8 pin connector that i just sent out in the mail today to the rma center. anyone know how long the process usually takes with them?
as the title states, i dont do any gaming really, just image/video rendering and my Q6600 serves me more than enough.. however i think i wanna upgrade my processor to a 45nm quad.. and at the same time i do see 2500k 1155 processors in the 200ish range and i'm seeing q9650s ranging from 170-200...
to get to the point, i have a p5q vanilla that shows no video, usb keyboard/mouse are not detected, no beeps from speaker.. the cpu socket has rows of pins that seem to be flat but i doubt that might be why.. i am starting to believe that the bios is corrupt. i have a m3a76-cm that im using...